Bus Conversion Magazine Bulletin Board

Bus Discussion => Bus Topics ( click here for quick start! ) => Topic started by: Barn Owl on June 05, 2006, 09:07:37 PM



Title: GM 4106 homemade tailpipe.
Post by: Barn Owl on June 05, 2006, 09:07:37 PM
Iím not sure if you guys like to see this kind of stuff, but I like to see what others are doing and how they solve their problems. I am new to bus ownership and I find these boards invaluable. Anyway, the previous owner lost the tailpipe and the exhaust shot straight to the ground. My driveway is 7/10ths of a mile of dirt/gravel uphill. Needless to say, I could not have done a better job of sweeping the gravel off than the bus did blowing the gravel off. The bus left a two foot swath of bare dirt the whole way up.† I could literally see the dust cloud being sucked up into the intake. I called a very reputable bus parts dealer and received a $67 + shipping quote for the tailpipe. I felt this one was one I would just do myself, so using some old scrap I welded one up. Total time - less than 2hrs. Here it is:


Title: Re: GM 4106 homemade tailpipe.
Post by: Nusa on June 05, 2006, 10:07:10 PM
Looks good. Of course, you still have to fix your driveway.


Title: Re: GM 4106 homemade tailpipe.
Post by: Geoff on June 06, 2006, 04:08:56 AM
I suspect the previous owner lost the tail pipe because he scraped it off on a low driveway-- I hope your new one doesn't do the same thing, it looks like it is the lowest point under the engine. 

--Geoff


Title: Re: GM 4106 homemade tailpipe.
Post by: Len Silva on June 06, 2006, 05:25:46 AM
I haven't dealt with this problem yet, but it's coming up.
I think I will opt to have the exhaust come out on the left instead of the rear.
This would let me better see the exhaust in the mirror and maybe keep some of the soot off the tow car.

Len


Title: Re: GM 4106 homemade tailpipe.
Post by: FloridaCliff on June 06, 2006, 09:08:18 AM
BarnOwl,

Looks Good!

I like seeing how others solve misc issues.

I, like Len may run mine out the drivers side when I replace the pipe this year.

Without the a/c I have an almost straight shot out the side.

Cliff


Title: Re: GM 4106 homemade tailpipe.
Post by: gus on June 06, 2006, 07:52:19 PM
Len

I thought about a left side pipe on my 4104 while replacing the mufflers. I decided against it after I pictured the exhaust blasting auto drivers alongside the bus at traffic lights or in heavy, slow moving traffic.

I'm still thinking about doing it at a 45* angle at the corner which wouldn't be so bad, but ground clearance is still a problem.


Title: Re: GM 4106 homemade tailpipe.
Post by: Barn Owl on June 06, 2006, 08:19:28 PM
My father wanted me to come up with a setup that would exit somewhere out the side but I donít see an easy solution for that yet. The radiator mount is low and in the way (see the last photo). The engine cradle is an obstacle for a behind the wheel exit. I would like to see photos if anyone has done a side exhaust for a 4106. Tomorrow will be my familyís first trip with the bus. We are going to do a two night trip close to home just to get a feel for things. I am hoping for a smooth trip because my wife is not totally sold on this bus thing.


Title: Re: GM 4106 homemade tailpipe.
Post by: Buffalo SpaceShip on June 06, 2006, 09:01:10 PM
Looks good, but be careful of those obstructions, as mentioned, or you'll be replacing it again in short order.

On my '06 and '08, I have no problem seeing the exhaust out of my left mirror, even though it's coming out of the back. You're right, the side radiator would place the pipe WAY too low.

Good lcuk on your trip!
Brian Brown
4106-1175
4108-216


Title: Re: GM 4106 homemade tailpipe.
Post by: NCbob on June 07, 2006, 06:58:39 AM
While we're on the topic of Exhaust systems...has anyone used the Aero Stainless muffler on a Detroit yet?  I noticed that my muffler, though having been repaired by the previous owner, will need to be replaced by next year.  Whatever baffles are left in it the Jakes will take care of in short order...

I spoke with the folks at Aero and they tell me that their muffler will match the back pressure componant required by Detroit Diesel for their 2 strokes.  Imagine...a Detroit that sounds like it's got a Smitty muffler....I might even opt for duals!  ;)

NCbob