Bus Conversions dot Com Bulletin Board
December 22, 2014, 01:58:37 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: If you had an Online Subscription:  It will not get lost in the mail.
   Home   Help Forum Rules Search Calendar Login Register BCM Home Page Contact BCM  
Pages: 1 [2]  All   Go Down
  Print  
Author Topic: Torque Multiplier  (Read 3024 times)
gus
Hero Member
*****
Offline Offline

Posts: 3546





Ignore
« Reply #15 on: October 12, 2010, 04:53:59 PM »

John,

Ash Flat is on Hwy 167 just south of MO. It is quite a bit east of Hwy 65, the route you would normally take from Branson to LR.

From here it is about the same distance to either LR or Branson on a dog leg route.

I will be here until Fri and back on Monday. Let me know your plans.
Logged

PD4107-152
PD4104-1274
Ash Flat, AR
JohnVickrey
Full Member
***
Offline Offline

Posts: 198


1960 PD 4104-4541




Ignore
« Reply #16 on: October 12, 2010, 06:45:04 PM »

Gus, Sorry I have missed you.... we are in Mcghee south of Pine Bluff. 

Lin, My apologies for hi jacking your thread. 

John
Logged

John Vickrey   -   Dearing, GA
About 2 hours East of ATL on I-20 and 4 miles south of I-20.
Got Electricity and Water for 4-5 coaches.  Less that a mile to a
dumpstation.  Stop by and sit a spell.
Lin
Hero Member
*****
Offline Offline

Posts: 4604

1965 MC-5a




Ignore
« Reply #17 on: October 25, 2010, 02:48:35 PM »

I bought one and it came today.  It works wonderfully if you turn it in the right direction.  I forgot the lug I tried it on first was left handed.  Fortunately I realized the error before I stripped the stud.  I will use 8# on a torque wrench to tighten up.  It would be very easy to go to far with this.
Logged

You don't have to believe everything you think.
gus
Hero Member
*****
Offline Offline

Posts: 3546





Ignore
« Reply #18 on: October 25, 2010, 03:57:41 PM »

Lin,

These things are designed for loosening nuts but they are not very accurate for torquing.  It is real easy to over torque with them. If it is like mine you can easily reach 1000 lb-ft.

You might want to check some of your torquing with a torque wrench just to make sure.
Logged

PD4107-152
PD4104-1274
Ash Flat, AR
Lin
Hero Member
*****
Offline Offline

Posts: 4604

1965 MC-5a




Ignore
« Reply #19 on: October 25, 2010, 04:16:01 PM »

Gus,

My torque wrench is really only good for up to 150 foot pounds.  I had thought that with a 60:1 rating, I could set the wrench to 8 ft/lbs and be within reason.  Do you think that this would not work?
Logged

You don't have to believe everything you think.
bevans6
Hero Member
*****
Offline Offline

Posts: 4883


1980 MCI MC-5C




Ignore
« Reply #20 on: October 25, 2010, 08:17:43 PM »

a torque wrench that is normally used to do up to 150 ft lbs is going to be horribly inaccurate at 8 ft lbs.  Each 1 lb error is going to be 60 ft lbs error after your multiplying by 60 times.  I would expect that your wrench, set for 8 ft lbs, will return somewhere between 5 and 10 and you'll never know which...   why not just use it to undo things, the way it's supposed to be used, and do the nuts up the old  fashioned way?  4 foot breaker bar and lean on it?

Brian
Logged

1980 MCI MC-5C, 8V-71T from a M-110 self propelled howitzer
Spicer 8844 4 speed Zen meditation device
Vintage race cars -
1978 Lola T440 Formula Ford
1972 NTM MK-4 B/SR
zubzub
Hero Member
*****
Offline Offline

Posts: 1168


'53 4104. Roadworthy but rough around the edges.


WWW

Ignore
« Reply #21 on: October 27, 2010, 08:46:18 AM »

a torque wrench that is normally used to do up to 150 ft lbs is going to be horribly inaccurate at 8 ft lbs.  Each 1 lb error is going to be 60 ft lbs error after your multiplying by 60 times.  I would expect that your wrench, set for 8 ft lbs, will return somewhere between 5 and 10 and you'll never know which...   why not just use it to undo things, the way it's supposed to be used, and do the nuts up the old  fashioned way?  4 foot breaker bar and lean on it?

Brian
This plus the fact that torque multipliers also have frictional loses (usually specified by the manufacturer) so you can add that to the mix and X it to your torque wrench's inaccuracies.
Logged

gus
Hero Member
*****
Offline Offline

Posts: 3546





Ignore
« Reply #22 on: October 27, 2010, 01:28:02 PM »

Lin,

A 3/8 torque wrench in inch-lbs will be more accurate but I don't think that will help much as per the above posts.

You can use your 150 lb-ft torque wrench with an extension to bring it up to 450-500 by using a little math. All you're doing is extending the length of your wrench handle, kind of a cheater bar effect.
Logged

PD4107-152
PD4104-1274
Ash Flat, AR
Pages: 1 [2]  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!