Bus Conversions dot Com Bulletin Board
December 19, 2014, 08:19:02 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: If you had an Online Subscription: You will not have to go out in the rain, sleet, hail, or snow to retrieve it.
   Home   Help Forum Rules Search Calendar Login Register BCM Home Page Contact BCM  
Pages: [1]   Go Down
  Print  
Author Topic: Wheel Seal part number cross reference MC 9, GM 4106, 4107  (Read 1912 times)
BC Bus
Jr. Member
**
Offline Offline

Posts: 80




Ignore
« on: July 07, 2011, 11:03:34 AM »

Does anyone have any non MCI Part numbers, Rockwell, CR, Timken, NAPA for rear drive axle oil seals for a MC 9 and all the related parts to replace the seal.

According to some web sites this is the same seal as the GMC 4106 4107

The MCI number for the seal is 15R-3-8 .
« Last Edit: July 07, 2011, 03:48:03 PM by BC Bus » Logged

GMC Buffalo  &  MC9

Always willing to help a Busnut !
Tom Y
Hero Member
*****
Offline Offline

Posts: 884


80 5C With Cummins L10 in Progress




Ignore
« Reply #1 on: July 07, 2011, 05:32:53 PM »

CR 45010 is the seal.  Tom Y
Logged

Tom Yaegle
Just Dallas
Bus Conversion Stuff on a Budget
Hero Member
*****
Offline Offline

Posts: 842



WWW

Ignore
« Reply #2 on: July 07, 2011, 05:37:59 PM »

Napa number: NOS 45010
Logged

I'm just an old chunk of coal... but I'm gonna be a diamond someday.
BC Bus
Jr. Member
**
Offline Offline

Posts: 80




Ignore
« Reply #3 on: July 07, 2011, 05:45:33 PM »

Thanks guys..I had a rockwell and stemco number but both of yours will really help.

Great board !
Logged

GMC Buffalo  &  MC9

Always willing to help a Busnut !
zubzub
Hero Member
*****
Offline Offline

Posts: 1168


'53 4104. Roadworthy but rough around the edges.


WWW

Ignore
« Reply #4 on: July 07, 2011, 06:59:41 PM »

Are 4104  #s the same?
Logged

Just Dallas
Bus Conversion Stuff on a Budget
Hero Member
*****
Offline Offline

Posts: 842



WWW

Ignore
« Reply #5 on: July 07, 2011, 07:15:32 PM »

Nope.

Scotseal 44964

Are 4104  #s the same?
Logged

I'm just an old chunk of coal... but I'm gonna be a diamond someday.
zubzub
Hero Member
*****
Offline Offline

Posts: 1168


'53 4104. Roadworthy but rough around the edges.


WWW

Ignore
« Reply #6 on: July 07, 2011, 11:43:48 PM »

Thank you.
Logged

Ralph7
Full Member
***
Offline Offline

Posts: 162




Ignore
« Reply #7 on: July 08, 2011, 05:28:34 AM »

 The  CR 45010 rides tooooo far in on the axle.(wiper).. --- I JUST INSTALLED THE 44964, also ----- I have a National  seal 370022A ----    AND if the wiper(on axle) is damaged it needs changed(PITA)  job .. The WIPER looks like it the housing, but is driven on.
  The   45010 on my left drive does not leak  but the right has a very slight taper??? cause I lost 2 seals!
  The 44964 seal does not go in far on the wiper, took hub off and there is a difference in depth of seal, the 44964 axle seal that sits on axle sits closer to the bearing.
  At this time I have a 45010 and a National 370022A  PLUS a wiper . will get  another 44964 . NO I am not a Huh?? just nut/pessamist, something is going to fail.
Logged
Just Dallas
Bus Conversion Stuff on a Budget
Hero Member
*****
Offline Offline

Posts: 842



WWW

Ignore
« Reply #8 on: July 08, 2011, 06:01:06 AM »

Ralph, the wiper shouldn't be a pain to remove. Just heat it with a propane torch and it will slide right off. Same with installing it. Heat the wiper up really good with a propane torch and it will slip right on.
If you drive it on you stand a good chance of warping it.
Logged

I'm just an old chunk of coal... but I'm gonna be a diamond someday.
Ralph7
Full Member
***
Offline Offline

Posts: 162




Ignore
« Reply #9 on: July 08, 2011, 07:43:30 AM »

  Thanks Dallas the one first one I removed from the right side was I think a national and I knew I was or had trouble when it was more effort was needed to get it the last 1/4in..
  We should have changed it down there! I had a 45010 with me. 
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!