Bus Conversions dot Com Bulletin Board
December 21, 2014, 02:09:13 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: If you had an Online Subscription: It takes up much less space in your bus.
   Home   Help Forum Rules Search Calendar Login Register BCM Home Page Contact BCM  
Pages: [1] 2  All   Go Down
  Print  
Author Topic: Cummins big cam 3 400 turbo setup  (Read 5566 times)
rusty
Sr. Member
****
Offline Offline

Posts: 363





Ignore
« on: January 27, 2013, 11:14:32 AM »

Tom C, and anyone else. The shop that does most of our work on larger motors was the one that told me I was stuck with want I have. I know that this shop goes by the book and is not interested in changing stock parts so I can understand why they gave that answer.
 The motor that I have is a Reman ( probably from Mexico ). The tag says it is a 1984 NTC 400 BC3. The CPI is 891-ff257. The motor SN is 60509711. Timing code is BY .065.
 The turbo is a Holset SN M 88924, Assy # 3523415, and Kit number 3801597 RX.
 With this information can you determine what turbo I could use to help with the soot problem. I am not interested in cutting the fuel back as I sometimes pull a trailer and need the power.

Thank You
Wayne
Logged
HB of CJ
Hero Member
*****
Online Online

Posts: 1305




Ignore
« Reply #1 on: January 27, 2013, 12:48:16 PM »

If anybody can clean up your BC3 400, they can.  Be aware of what the CPL says it has in it; vs. what the engine ACTUALLY has in it.  May be a big difference inside.  You may have to do a look-and-see.  HB of CJ (old coot)
Logged
azdieselman
Jr. Member
**
Offline Offline

Posts: 63




Ignore
« Reply #2 on: January 27, 2013, 07:48:59 PM »

When I ran your ESN, I came up with a 3801598RX. It's a dual entry turbo, So it may be an HT4B. I'm not sure what your soot problem is about. Do you run at a low rpm?
Logged

1980 Mod 10
rusty
Sr. Member
****
Offline Offline

Posts: 363





Ignore
« Reply #3 on: January 28, 2013, 06:06:24 AM »

No I run at 1850 RPM. I think the fuel is not being completely burnt. That's why Tom is on the right track, to much fuel or a to small turbo. I hope we can find a larger turbo. The only other problem could be to small of muffler. It is a 5 inch in and out. Both inlet and outlet on the same end.

Wayne



Logged
luvrbus
Hero Member
*****
Offline Offline

Posts: 13129




Ignore
« Reply #4 on: January 28, 2013, 06:44:03 AM »

Wayne, I never owned a 855 that would run over 3 or 4,000 hrs without changing injectors fwiw they are also bad about cam wear.

When we rebuilt that engine we installed the N-14 liners and pistons that done away with the white smoke on start up also great engines but they do smoke the

 You start changing turbos you will give hp and torque up in some range either on top end mid range or the lower end BTDT

good luck
« Last Edit: January 28, 2013, 06:50:47 AM by luvrbus » Logged

Life is short drink the good wine first
azdieselman
Jr. Member
**
Offline Offline

Posts: 63




Ignore
« Reply #5 on: January 28, 2013, 06:59:47 AM »

Clifford beat me to it. I would have the overhead checked. Not just adjusted, But checked, See if it is loose. The #1 cause of cam failure is a loose injector train. Pull the injectors and have them cleaned. If you find any that are really loose, You can pull the pan and inspect the cam from below. Do you have a boost gauge? You could have an intake leak also. Does this have a pulse manifold?
Logged

1980 Mod 10
rusty
Sr. Member
****
Offline Offline

Posts: 363





Ignore
« Reply #6 on: January 28, 2013, 07:15:07 AM »

The overhead has been done on a regular interval. In fact it has just been done before the last trip. The shop that does it is a well respected shop and when I had mine done there was another 400 they were working on. Clifford if you use an average of 50 miles an hour I have some where around 2200 hours on that motor. I would still be interested if there is a different turbo and what I would have to give up for it.

Wayne
Logged
Uglydog56
Sr. Member
****
Offline Offline

Posts: 269


I'd rather be lucky than good.




Ignore
« Reply #7 on: January 28, 2013, 12:13:14 PM »

Pittsburgh Power has a turbo upgrade for you engine.  I think 5" is pretty marginal for exhaust at your horsepower level.  I would also take a look at the intake piping to make sure it is adequate, at least 6".
Logged

Rick A. Cone
Silverdale, WA
66 Crowny Crown "The Ark"
luvrbus
Hero Member
*****
Offline Offline

Posts: 13129




Ignore
« Reply #8 on: January 28, 2013, 12:38:04 PM »

Wayne, here is the flow rates on your engine if it will help

Intake    1000 cfm
Exhaust  2426 cfm
exhaust temp should be 850 degrees  @2100 always start here makes life a lot easier 5 inch should be good that will give you 3829 cfm flow with a straight pipe 45's and 90 bends will reduce the flow rate
 
good luck
« Last Edit: January 28, 2013, 01:26:20 PM by luvrbus » Logged

Life is short drink the good wine first
TomC
Hero Member
*****
Offline Offline

Posts: 6979





Ignore
« Reply #9 on: January 28, 2013, 04:19:46 PM »

5" exhaust is used on a 4 stroke up to 600hp. Check your muffler-maybe too stuffed. Donaldson makes a 5" same side in and out that is made for turbo engines. I have one on my 8V-71 and it makes a very pleasant exhaust note. If your muffler is stuffed to the point that you can't here the exhaust note at all-maybe time for a new muffler. They aren't especially expensive. Good Luck, TomC
Logged

Tom & Donna Christman. '77 AMGeneral 10240B; 8V-71TATAIC V730.
Ralph7
Full Member
***
Offline Offline

Posts: 162




Ignore
« Reply #10 on: January 28, 2013, 06:23:36 PM »

   Do you have a air to air after cooler, it would take 2 people to check for a small hole in one of the hoses , the next check is pressure test the cooler, but KONW you can blow it, it only takes a cracked tube to cause problems.
   Holes in the connector hoses are hard to find, and you can get a slight burn.
Logged
luvrbus
Hero Member
*****
Offline Offline

Posts: 13129




Ignore
« Reply #11 on: January 28, 2013, 06:32:48 PM »

All the BC 400's we had were water after cooled
Logged

Life is short drink the good wine first
chessie4905
Hero Member
*****
Offline Offline

Posts: 793





Ignore
« Reply #12 on: January 28, 2013, 07:01:16 PM »

maybe it has already been done, but I'd put a restriction tattle tale  gauge on the turbo inlet to check for restriction, put a boost gage to check boost, and put a low pressure gauge into exhaust outlet to check for restriction before I spent more money on parts or guessing. Gauges are fairly cheap and can be temp installed for diagnostics.
Logged

GMC h8h 649#028
Pennsylvania-central
RickB
Hero Member
*****
Offline Offline

Posts: 1079


81 MCI 9 smooth side 8V71 Allison 754




Ignore
« Reply #13 on: January 28, 2013, 08:37:55 PM »

Wayne, Personally I think that motor is toast and you should buy a replacement. I'd take the old motor off your hands and dispose of it properly for you because I'm just such a good guy though.

You're not buying that line of thinking are you? Darn.

It was worth a try.

RB
Logged

I will drive my Detroit hard... I will drive my Detroit hard.
rusty
Sr. Member
****
Offline Offline

Posts: 363





Ignore
« Reply #14 on: January 29, 2013, 06:14:35 AM »

Clifford is correct it is a water after cooled. I do have a gauge on the inlet pipe and it did have a restriction so I but another air filter on it. That did not seem to help. I have taken the filter out and ran the motor and it does not make a difference. I do not have a boost gauge or a back pressure gauge. Maybe that is the next step or maybe just run it another 100,000 miles and buy more soap.

Sorry Rick  If you are this way next summer stop by.

Wayne
Logged
Pages: [1] 2  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!