Bus Conversions dot Com Bulletin Board
October 24, 2014, 10:48:44 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: If you had an Online Subscription: You will not have to go out in the rain, sleet, hail, or snow to retrieve it.
   Home   Help Forum Rules Search Calendar Login Register BCM Home Page Contact BCM  
Pages: 1 [2]  All   Go Down
  Print  
Author Topic: Oil Filter Wrench  (Read 1142 times)
loveshack
62 pd 4106
Jr. Member
**
Offline Offline

Posts: 74


1962 pd4106




Ignore
« Reply #15 on: June 20, 2014, 07:13:49 PM »

I use a strap wrench works great!
Logged

Bruce E.                                                                        62 pd4106 vs730.                   
Gonic N.H.
krank
Full Member
***
Offline Offline

Posts: 132





Ignore
« Reply #16 on: June 20, 2014, 07:50:50 PM »

I usually use filter pliers, similar to channel locks but made specifically for filters. I also punch a hole in the bottom to drain the filter before spinning it off - less mess.
Logged

Jim Eh.
1996 MC12
6V92TA / HT741D
(Sunchaser)
Winnipeg, MB.
opus
Hero Member
*****
Offline Offline

Posts: 507





Ignore
« Reply #17 on: June 20, 2014, 09:00:13 PM »

I usually use filter pliers, similar to channel locks but made specifically for filters. I also punch a hole in the bottom to drain the filter before spinning it off - less mess.


Always poke a hole.  Pliers wont work in my setup. 

I went with this: http://www.amazon.com/HD-Oil-Filter-Strap-Wrench/dp/B000I1APIS
Logged

1995 BB All-American - A Transformation.
Oonrahnjay
Hero Member
*****
Offline Offline

Posts: 1512





Ignore
« Reply #18 on: June 21, 2014, 03:29:48 PM »

I have the strap type. Always able to get the filter off. It will crush the spin on filter, but you're throwing the filter away anyway. The main trick to getting a spin on filter off is not to tighten to tight in the first place. Just tighten with hand pressure, never use a filter wrench to tighten. Good Luck, TomC 

     And lightly oil both sides of the gasket and watch that it doesn't get pinched or pushed out of place.  It helps the filter go in smoothly and -- if the gasket is damaged -- it will spray oil like ... well, pretty much like most of the gasket faces on a DD 2-stroke ...
Logged

Bruce H; Wallace (near Wilmington) NC
1976 Daimler (British) Double-Decker Bus; 34' long
6-cyl, 4-stroke, Leyland O-680 engine

(New Email -- brucebearnc@ (theGoogle gmail place) .com)
wg4t50
Hero Member
*****
Offline Offline

Posts: 802





Ignore
« Reply #19 on: June 21, 2014, 03:45:35 PM »

I find the strap type wrapped around the square tube that fits the 1/2" drive or use a 3/4" open wrench. That setup will remove most any filter as long as you use it correctly.
Dave M  
Logged

MCI7 20+ Yrs
Foretravel w/ISM500
WG4T CW for over 50 wpm for ever.
Central Virginia
eagle19952
Hero Member
*****
Offline Offline

Posts: 1289




Ignore
« Reply #20 on: June 21, 2014, 07:09:17 PM »

I found yhe CAT filter wrench...14$...

http://www.amazon.com/Caterpillar-Filter-Strap-Wrench-185-3630/dp/B004TR4B7S/ref=sr_1_2?ie=UTF8&qid=1403402894&sr=8-2&keywords=caterpillar+filter+wrench
Logged

Donald PH
1978 Model 05 Eagle w/Torsilastic Suspension,8V71 NA, DDAllison on 24.5's 12kw Kubota.
Wants Paint Smiley
Previously owned by Wee Willie Ent.
Pages: 1 [2]  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!