Bus Conversions dot Com Bulletin Board
October 01, 2014, 11:28:54 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: This BB is intended for the sole purpose of sharing conversion and bus related information among visitors to our web site. These rules must be followed in order for us to continue this free exchange of info. No bad mouthing of any business or individual is permitted. Absolutely no items for sale are to be posted, except in the Spare Tire board. Interested in placing a classified or web ad, please contact our advertising dept. at 714-903-1784 or e-mail to: info@busconversions.com.

   Home   Help Forum Rules Search Calendar Login Register BCM Home Page Contact BCM  
Pages: [1]   Go Down
  Print  
Author Topic: mci 102c3 axle ratio Id help  (Read 371 times)
oldfordlover36
Newbie
*
Offline Offline

Posts: 16




Ignore
« on: July 28, 2014, 04:03:25 PM »

I have a 1993 mci 102c3 with an auto transmission and wondering how I can tell the rear axle ratio.  The tag on the rear end just has a serial number and a build date no ratio listed.  I looked on rockwell/meritorious website and my number dosent match any of their listed formats to decipher the ratio.  Any ideas?
Logged
robertglines1
steam nut
Hero Member
*****
Offline Offline

Posts: 4014





Ignore
« Reply #1 on: July 28, 2014, 04:42:50 PM »

ck end of pinion shaft.
Logged

Bob@Judy  98 XLE prevost with 3 slides --Home done---last one! SW INdiana
luvrbus
Hero Member
*****
Offline Offline

Posts: 12591




Ignore
« Reply #2 on: July 28, 2014, 04:53:00 PM »

Robert is correct it is stamped on the pinon shaft,it would help if we knew what engine and transmission the bus has,the 3:36 was standard for the 6v92 and 740 Allison the 3:70 was a option
« Last Edit: July 28, 2014, 05:53:18 PM by luvrbus » Logged

Life is short drink the good wine first
sledhead
Sr. Member
****
Offline Offline

Posts: 342





Ignore
« Reply #3 on: July 28, 2014, 05:07:29 PM »

on my 1990 mci 102c with a 6v92ta and ht 740 auto it is 333

dave
Logged

1990 mci 102c  6v92 ta ht740  kit,living room slide . home base huntsville ontario canada
lostagain
Hero Member
*****
Offline Offline

Posts: 1531


MC5C




Ignore
« Reply #4 on: July 28, 2014, 05:25:51 PM »

I think mine is a 3.36. 6V92 and Allison 740 on my 5C. But yea, it is stamped on the end of the pinion shaft.


Sent from my iPhone using Tapatalk
Logged

JC
Invermere, BC
1977 MC5C, 6V92/HT740
oldfordlover36
Newbie
*
Offline Offline

Posts: 16




Ignore
« Reply #5 on: July 28, 2014, 06:39:16 PM »

I apoligise it has a l10 cummins and a ht740.  The ecm went south and I need to tell the programmer the ratio.  I will look on the pinion u guys are the best thanks and Robert I love your prevost project!
Logged
luvrbus
Hero Member
*****
Offline Offline

Posts: 12591




Ignore
« Reply #6 on: July 28, 2014, 07:14:36 PM »

Only problem with finding the ratio on the pinion sometimes you need to remove the yoke to see it, if all else fails jack it up and count the revolutions 

 
Logged

Life is short drink the good wine first
TomC
Hero Member
*****
Offline Offline

Posts: 6815





Ignore
« Reply #7 on: July 28, 2014, 09:32:31 PM »

If you have a GPS, and tachometer, you could just note the rpm's at 60mph then look up your tire size as to how many revs per mile it turns.  For instance, at 60mph, if you have 11R-24.5 that turn 476rpm and the engine is turning 1585rpm, then divide 1585 by 476 and you come up with 3.33. Or you can lift up one tire and count the drive shaft revolutions. If only one wheel is up, it will be double. Good Luck, TomC
Logged

Tom & Donna Christman. '77 AMGeneral 10240B; 8V-71TATAIC V730.
blue_goose
Sr. Member
****
Offline Offline

Posts: 285





Ignore
« Reply #8 on: July 29, 2014, 11:42:45 AM »

If you have a tack check rpm and mph.  My 102C3 had a 3.36.  I have a good set of gears for a 3.36 if you need them.

Jack
Logged

Data used in this document is made from 100% recycled electrons and magnetic particles. No electrons were harmed in the creation of this document.
oldfordlover36
Newbie
*
Offline Offline

Posts: 16




Ignore
« Reply #9 on: July 29, 2014, 08:28:54 PM »

Went to look at the pinion and found another label covered in grease right under it and said 3.21 gear ratio thanks for all the help!  I will get a build thread going one of these days when I get a chance to show u all what I'm doing thanks again.
Tyson
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!